ERouting OSPF PT Practice SBA :
A few things to keep in mind while completing this activity:
1. Do not use the browser Back button or close or reload any exam windows during the
exam.
2. Do not close Packet Tracer when you are done. It will close automatically.
3. Click the Submit Assessment button to submit your work.
Introduction
In this practice Packet Tracer Skills Exam, you will:
- finish the configuration of a partially configured network
- establish connectivity to the UK and the Internet through the use of static and dynamic routing
Addressing Table

Note: The password for user EXEC mode is cisco. The password for privileged EXEC mode is class.
Step 1: Finish the IP Addressing.
Note: Initially, you can only access router US-R2 through the console connection on US-
Admin.
a. Configure and verify interface addressing on US-R2.
Configure and activate all interfaces for US-R2 that are listed in the
addressing table.
b. Configure the correct IP addresses on US-PC2 and US-R1.
Configure US-PC2 with the last IP address in the subnet.
Configure the Fa0/1 interface on US-R1 with the last IP address in the
subnet.
c. Verify connectivity.
Step 2: Discover the Network.
Explore the network to determine the IP addressing of the serial interfaces that US-
HQ shares with US-R1 and US-R2.
Remotely access US-HQ. US-R1# telnet 192.168.20.245
Step 3: Configure Static and Default Routing.
a. Configure connectivity to the UK.
- Using the next hop address 128.107.25.2, configure one summary static route on US-HQ to include only the subnets used and reserved for the UK. The UK subnets are listed in the following table:
HQ(config)# ip route 10.10.0.0 255.255.255.252 128.107.25.2

- Configure a default route on US-HQ to send to the Internet all other traffic for destinations that are not found in the US-HQ routing table. Use the outbound interface argument.
HQ(config)# ip route 0.0.0.0 0.0.0.0 S0/1/0
b. Verify static and default routing.
Step 4: Configure OSPF Routing.
a. Configure OSPF on US-HQ, US-R1, and US-R2.
Use OSPF process ID 3 and area 0.
Advertise each subnet individually with its corresponding wildcard mask. On US-HQ, do not advertise the subnet to the Internet or the subnet to UK.
HQ(config)# router ospf 3
HQ(config-router)# network 192.168.20.244 0.0.0.3 area 0
HQ(config-router)# network 192.168.20.240 0.0.0.3 area 0
US-R1 (config)# router ospf 3
US-R1 (config-router)# network 192.168.20.0 0.0.0.63 area 0
US-R1 (config-router)# network 192.168.20.112 0.0.0.7 area 0
US-R1 (config-router)# network 192.168.20.244 0.0.0.3 area 0
US-R2 (config)# router ospf 3
US-R2 (config-router)# network 192.168.20.64 0.0.0.31 area 0
US-R2 (config-router)# network 192.168.20.112 0.0.0.7 area 0
US-R2 (config-router)# network 192.168.20.240 0.0.0.3 area 0
Disable OSPF updates out interfaces where there are no OSPF
neighbors available.
HQ(config-router)# passive-interface s0/1/0
HQ(config-router)# passive-interface s0/1/1
US-R1 (config-router)# passive-interface fa0/0
US-R2 (config-router)# passive-interface fa0/0
Configure US-HQ to send the default route to US-R1 and US-R2 in
OSPF updates.
HQ(config-router)# default-information originate
b. Modify the default OSPF operation.
Configure US-R1 to always be the DR by using a priority of 150.
Pour Fa0/1 , S0/0
US-R1 (config-if)# ip ospf priority 150
Configure US-R2 to always be the BDR by using a priority of 75.
Pour Fa0/1 , S0/0
US-R2 (config-if)# ip ospf priority 75
Change the hello interval to 30 seconds on US-R1 and US-R2 for the
LAN that these two routers share with ServerLAN.
US-R1 (config-if)# ip ospf hello-interval 30
US-R2 (config-if)# ip ospf hello-interval 30
Verify OSPF neighbor status.
US-R1# show ip ospf neighbor
c. Verify that OSPF is fully operational.
Verify that the routing tables on US-R1, US-R2, and US-HQ contain all
the expected routes. It may be necessary to shutdown and then
reactivate interfaces to force OSPF to converge.
US-R1# show ip route
Step 5: Verify Full Connectivity.
Although these are not scored, the following connectivity tests should be successful.
To test the static route to UK, successfully ping between US-HQ and UK-PC1.
To test the OSPF neighbor establishment with ServerLAN, successfully ping between
US-Admin and www.xyzcorp.com.
To test end-to-end connectivity between the US and UK, successfully ping between
US-PC2 and UK-PC3.
To test the default route, successfully ping the Cisco Server from US-Admin.
==============================
SUMMARY:
US-PC2
------
192.168.20.94
255.255.255.224
192.168.20.65
US-R2
=====
cisco enable class config ter
interface fa0/0
ip add 192.168.20.65 255.255.255.224 no shutdown
exit
inteface fa0/1
ip add 192.168.20.113 255.255.255.248 no shutdown
exit
interface s0/0/0
ip add 192.168.20.242 255.255.255.252 no shutdown
exit
inteface Lo0
ip add 172.16.0.2 255.255.255.255 no shutdown
exit
router ospf 3
network 192.168.20.64 0.0.0.31 area 0 network 192.168.20.112 0.0.0.7 area 0 network 192.168.20.240 0.0.0.3 area 0 passive-interface fastEternet 0/0
interface s0/0/0
ip ospf priority 75 exit
interface f0/1
ip ospf priority 75 exit
inteface f0/1
ip ospf hello-interval 30 end
show ip route
=================
Telnet
telnet 192.168.20.240
=====================
US-HQ
--------
cisco enable class
show ip route
conf term
ip route 10.10.0.0 255.255.252.0 128.107.25.2 ip route 0.0.0.0 0.0.0.0 s0/1/0
router ospf 3
network 192.168.20.244 0.0.0.3 area 0 network 192.168.20.240 0.0.0.3 area 0 default-information originate passive-interface s0/1/0
passive interface s0/1/1
exit
show ip route
=================
Open US-R1
=====================
US-R1
--------
cisco enable class
config term
interface fa0/1
ip add 192.168.20.118 255.255.255.248 no shutdown
exit
router ospf 3
network 192.168.20.0 0.0.0.63 area 0 network 192.168.20.112 0.0.0.7 area 0 network 192.168.20.244 0.0.0.3 area 0
passive-interface fa0/0 exit
do wr
interface f0/1
ip ospf priority 150
ip ospf hello-interval 30
exit
interface s0/0/0
ip ospf priority 150 exit
show ip route
exit
*************************
US-HQ
------
Serial0/0/0 192.168.20.245
Serial0/0/1 192.168.20.241
Serial0/1/0 64.100.50.2
Serial0/1/1 128.107.25.1
Download Full PDF file:
https://www.box.com/s/k2pr1xwe8yiyefznbjs3Have Fun!!
This is very interesting post and I learned so much from your blog. Do posting more.
ReplyDeleteccna Training institute in Chennai
ccna institute in Chennai
gst classes in Chennai
ReactJS Training in Chennai
Salesforce Training in Chennai
Tally course in Chennai
Web Designing Course in Chennai
ux design course in Chennai
Web Designing Course in anna nagar
Great Article Cyber Security Projects projects for cse Networking Security Projects JavaScript Training in Chennai JavaScript Training in Chennai The Angular Training covers a wide range of topics including Components, Angular Directives, Angular Services, Pipes, security fundamentals, Routing, and Angular programmability. The new Angular TRaining will lay the foundation you need to specialise in Single Page Application developer. Angular Training
Delete
ReplyDeleteThis content of information has
helped me a lot. It is very well explained and easy to understand.
seo training classes
seo training course
seo training institute in chennai
seo training institutes
seo courses in chennai
seo institutes in chennai
seo classes in chennai
seo training center in chennai
ReplyDeleteYou write this post very carefully I think, which is easily understandable to me. Not only this, but another post is also good. As a newbie, this info is really helpful for me. Thanks to you.
Tally ERP 9 Training
tally classes
Tally Training institute in Chennai
Tally course in Chennai
I really appreciate your method to explaining, I hope to see more posts from your blog. thank you!
ReplyDeleteDigital Marketing Course In Kolkata
Web Design Course In Kolkata
SEO Course In Kolkata